Part Analysis
| General Data | |
| Manufacturer (OEM) | Andyson |
| PCB Type | Double-Sided |
| Primary Side | |
| Transient Filter | 4x Y caps, 2x X caps, 2x CM chokes, 1x MOV |
| Inrush Protection | NTC Thermistor SCK205R0 (5 Ohm @ 25°C) & Relay |
| Bridge Rectifier(s) |
2x GBU1006 (420V, 15A @ 100°C)
|
| APFC MOSFETs |
2x Perfect PWE120N65SFMF (650V, 20A @ 100°C, Rds(on): 120mOhm)
|
| APFC Boost Diode |
1x WeEn BYC10-600P (600V, 20A @ 127°C)
|
| Bulk Cap(s) |
2x Nichicon (420V, 390uF each or 780uf combined, 2000h @ 105°C, GL)
|
| Main Switchers |
4x Chongqing Pingwei 18N50MF (500V, 18A @ 25°C, Rds(on): 0.3Ohm)
|
| APFC Controller |
Champion CM6500UNX
|
| Resonant Controller | Champion CU6901VPA |
| Topology |
Primary side: APFC, Full-Bridge & LLC converter
Secondary side: Synchronous Rectification & DC-DC converters |
| Secondary Side | |
| +12V MOSFETs | 6x Allpower APG013N04G-AU (40V, 100A @ 100°C, Rds(on): 1.3mOhm) |
| 5V & 3.3V | DC-DC Converters: 6x Nexperia PSMN4R0-30YLD (30V, 95A @ 25°C, Rds(on): 4mOhm) PWM Controller(s): ANPEC APW7159C |
| Filtering Capacitors | Electrolytic: 7x Nippon Chemi-Con (2-5,000 @ 105°C, KZE), 4x Rubycon (6-10000 @ 105°C, ZLH), 1x Nichicon (4-10,000 @ 105°C, HE)Polymer: 25x Polycap, 5x FPCAP, 1x Nippon Chemi-Con LE |
| Supervisor IC | Weltrend WT7527RA (OCP, OTP, OVP, UVP, SCP, PG) |
| MicroController / Fan Controller | Weltrend WT51F104 |
| Fan Model | Hong Hua HA1225M12F-Z (120mm, 12V, 0.45A, Fluid Dynamic Bearing) |
| 5VSB Circuit | |
| Rectifier |
PJ335M
|
| Standby PWM Controller | Excelliance MOS EM8569C |
Andyson provides the platform, which uses a contemporary design. The primary side has a full-bridge topology and an LLC resonant converter for reduced energy losses. On the secondary side, six Allpower FETs regulate the 12V rail, which feeds a pair of DC-DC converters that generate the minor rails. The build quality is good, and quality caps are on both the primary and secondary sides. On the contrary, the FETs used on the APFC converter, the full-bridge topology, and for the regulation of the 12V rails are from less-known manufacturers. Lastly, the soldering quality is satisfactory, as was the case in the 1000W model (but not in the 1200W unit).
The cooling fan is made by Hong Hua, so it is of good quality and will last long if you don’t stress it under high operating temperatures (above 40 degrees Celsius). Because of the PSU’s compact dimensions, a 120mm fan was used instead of a larger one, which would offer the same airflow at lower speeds, reducing the average noise output.
OEM not is andyson，It should dongguan UNEEC (cheng ming) Technology