Noise Output
Fan Full Speed, 75% & 50%
 |
 |
 |
Noise is not that high at full speed, compared to other cards, at close to 48.1 dBA. At 75% fan speed, it is at 38.5 dBA; at 50%, it drops notably lower to 24.2 dBA.
Idle, Multimedia & Rendering
 |
 |
 |
Thanks to the fan-stop feature, most graphics cards are dead quiet at idle and multimedia. The Galax RTX 5080 is also silent in rendering.
Gaming
 |
 |
 |
During short gaming periods, the Galax card is silent.
Furmark
In Furmark, where the card is stressed, the output noise is above 29 dBA, which is high enough.
Frequency Plots
30% Fan Speed (Min Fan Speed)
- Peak Frequency: 1 KHz
41% Fan Speed (Rendering – AVG RPM)
- Peak Frequency: 1 KHz
47% Fan Speed (Rendering – 1% High PRM)
- Peak Frequency: 1 KHz
49% Fan Speed (Gaming RTX OFF – AVG PRM)
- Peak Frequency: 1 KHz
50% Fan Speed (Gaming RTX/DLSS/FG ON – 1% High RPM)
- Peak Frequency: 1 KHz
51% Fan Speed (Gaming RTX Off – 1% High RPM)
- Peak Frequency: 1 KHz
57% Fan Speed (Furmark – AVG RPM)
- Peak Frequency: 1 KHz
58% Fan Speed (Furmark – 1% High RPM)
- Peak Frequency: 1 KHz
75% Fan Speed
- Peak Frequency: 1 KHz
100% Fan Speed
- Peak Frequency: 1.6 KHz
Signal Recordings
I have recorded the signals shown above, but please keep in mind that I’ve enabled Automatic Gain Control (AGC) to do so to make it easier for you to reproduce them. The provided recordings are only offered for aural identification purposes.
30% Fan Speed
41% Fan Speed
47% Fan Speed
49% Fan Speed
50% Fan Speed
51% Fan Speed
57% Fan Speed
58% Fan Speed
75% Fan Speed
100% Fan Speed
Pages:
- Prologue & Technical specifications
- NVIDIA’s Key Technologies
- Box & Contents
- Part Analysis
- Specifications Comparison
- Test System
- Game Benchmark Details
- Raster Performance
- RT Performance
- RT Performance + DLSS/FSR Balanced
- Raytracing Performance + DLSS/FSR Balanced + FG
- DLSS/FSR Balanced (No RT)
- DLSS/FSR Balanced + FG (No RT)
- Relative Perf & Perf Per Watt (Raster)
- Relative Perf & Perf Per Watt (Raster + DLSS/FSR)
- Relative Perf & Perf Per Watt (RT)
- Relative Perf & Perf Per Watt (RT + DLSS/FSR)
- Relative Perf & Perf Per Watt (RT + DLSS/FSR + FG)
- Rendering Performance
- Operating Temperatures
- Operating Noise & Frequency Analysis
- Power Consumption
- Clock Speeds & Overclocking
- Cooling Performance
- Epilogue
why dont you report on coil whine? i care about that more than anything else
Εξαιρετική παρουσίαση της RTX 5080 καρτας γραφικων! Οπως ειπωθηκε σωστα στο βιντεο εδω δεν βλεπουμε μια νεα καρτα απο θεμα επιδοσεων hardware,αλλα απο θεμα νεου software! Οπως τοτε με τη 7000 Gen της Radeon με απιστευτη αυξηση FPS μεσω του Fidelity 3 ετσι και τωρα βλεπουμε μια νεα gen στο θεμα DLSS4 και τιποτα παραπανω!
Aris i have an Andyson PX-1200 Platinum with ATX 2.53 spec should it okay to handle RTX 5080 with 12v-2×6 converter ?
power wise is ok, but I don’t trust adapters/converters.
did the 12v-2×6 converter still had bad melting behavior in RTX 50xx series with high wattage PSU like 1000W++, and do you have any suggestion for ATX 2.53 users who want to pairs their PSU with RTX 50xx series ?
There will always be issues in everything, but the fact is that 12V-2×6 is much safer than 12VHPWR. As for ATX 2.53 users, get proper cables from the respective brands, 2x 8-pin to 12+4